Mr Triều : 0906 815 828 , E Mail : info@duongtrieuanh.com
Tel : 028 3636 28 85 .
Fax : 028 3636 28 85
Chuyên cung cấp
thiết bị điện – Thiết bi công nghiệp – tự động hóa – Phụ tùng máy sản xuất
cho các nhà máy sản xuất tại Việt Nam
Nguồn hàng được nhập khẩu trực tiếp – uy tín và chất lượng
các nước trên thế giới như : Đức, Nhật, USA, ý, Hàn quốc …
| FJ 01510-000 | Flojet Viet nam |
| FJ 20325-031 | Flojet Viet nam |
| FJ 20325-033 | Flojet Viet nam |
| FJ 20465-001 | Flojet Viet nam |
| FJ 20408-000 | Flojet Viet nam |
| FJ 20466-006 | Flojet Viet nam |
| FJ 20467-006 | Flojet Viet nam |
| FJ 20468-005 | Flojet Viet nam |
| FJ 20469-006 | Flojet Viet nam |
| FJ 21000-233B | Flojet Viet nam |
Pump Design ............................................Duplex Diaphragm
Wetted Parts
Diaphragm Material........ Santoprene®, Viton ®, Buna, or Geolast
Check Valve Material .......Santoprene®, Viton ®, Buna, or Geolast
Housing material ........................................Acetal Copolymer
Ports ............................Gas Inlet & Outlet 1/4” (6.3 mm) Barb
Product Inlet 3/8” (9.5 mm) Barb
Product Outlet 3/8” (9.5 mm) Barb
Net Weight ......................................................1.10 lb. (0.5 Kg)
® A registered trade mark of Monsanto Co. ® A registered trade mark of I.E. DuPont Co.
PERFORMANCE SPECIFICATIONS
PUMP
Liquid Temperature Min ..............................................40°F (4°C)
............................Max ..........................................120°F (49°C)
Priming ..............Dry ..........................................28 ft. (8.5 m)
............................Wet ..........................................32 ft. (9.8 m)
Flow Rates ........Max ....................Up to 2.5 GPM (9.5 LPM)
Gas Supply Pressure ................20 to 80 PSI (1.4 to 5.6 bar)
Noise Level ........Max ......................................................87dB
STANDARD MODELS
N5100-010 ..........Buna
N5100-020 ..........Viton®
N5100-040 ..........Santoprene®
N5100-050 ..........Geolast®
DESCRIPTION
FLOJET Industrial N5100 Series Pumps are designed for
light general commercial and industrial applications.
These pumps are constructed from a selection of
materials for handling a broad range of chemicals*.
NOTE: Not to be used with any Fluids with a flash point
below 100˚F (38˚C).
*For Chemical Compatibality of diaphragm material
please refer to the Chemical Compatibility Guide
referenced in F100-227.
Santoprene®, Viton ®, Buna, or Geolast Material with 1/2” Ports
N5100 Series
Industrial Air Driven Pump
DIMENSIONAL DRAWING
Inches (millimeters)
Dimensional tolerances
± 0.06 inches
Consult factory if precise
details are required.
Flow in GPM (LPM)
*Indicates Air Inlet Pressure in PSI
Pressure in PSI (Bar)
INSTALLATION & OPERATION INFORMATION FOR MODELS N5100XXX
NOTE: For maximum running life do not exceed
80 PSI (5.5 bar) Gas Inlet Pressure
MOUNTING
The FLOJET N5100 Series self-priming pump should be
mounted in a dry and adequately ventilated area. This
pump can be mounted several feet from the tank, above
or below the fluid level. For most applications, no more
than 4 feet above the fluid level is recommended. This
is not a submersible pump.
Secure Pump to desired fixture by screws through the
mountng bracket. Ports must be facing down.
HOSE CONNECTIONS
Product In - Use 3/8” (10 mm), reinforced, flexible,
non-collapsible hose or equivalent. Avoid sharp bends
that could restrict flow or cause hose to collapse under
vacuum.
Product Out - Use reinforced 3/8” (10 mm) I.D. hose
for discharge tube.
Gas In - Make sure gas regulator is set at zero. Use
reinforced 1/4” (6 mm) hose. connect “Gas In” to gas
supply fitting on regulator. If pumps are installed in an
enclosed area, it is recommended to connect a hose
to the gas discharge port (exhaust) and vent gas to
atmosphere. (Requires ‘small’ exhaust port)
PLUMBING
Use a flexible hose to avoid excess stress on pump
ports. DO NOT crimp or kink hose. All hose should be
the same size as the pump port fittings.
All fittings must be compatible with fluid being pumped.
It is recommended to use plastic fittings only.
The use of check valves in the plumbing system could
interfere with the priming ability of the pump. If
unavoidable, check valves in the pumping system must
have a cracking pressure of 2 PSI or less.
Use a minimum 40 mesh strainer or filter in the tank or
pump inlet line to keep large foreign particles out of the
system.
OPERATION
At start-up, regulate gas pressure to desired setting. For
most installations 20 PSI (1.4 bar) inlet will be adequate,
although DO NOT go below 20 PSI (1.4 bar). Pump will
operate according to air supply. Flow and pressure can
be adjusted by increasing or decreasing gas pressure to
accommodate varying product viscosities, length of
lines or other installation conditions. Review flow curves
located on page 1 for further assistance. High viscosity
fluids and hose length will limit priming distance.
IF PUMP IS T0 BE USED IN HIGH FLOW, LOW
PRESSURE APPLICATIONS, ADJUST GAS PRESSURE
TO 20 PSI (1.4 BAR) ABOVE DISCHARGE PRESSURE.
CONTINUOUS OPERAT
Không có nhận xét nào:
Đăng nhận xét